| Customization: | Available |
|---|---|
| Customized: | Non-Customized |
| Certification: | ISO |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Oder code
Specification:
| Bore size: | 6 | 10 | 16 | 20 | 25 | 32 |
| Acting type: | Double Acting | |||||
| Fluid: | Air(to be filtered by 40μm filter element) | |||||
| Operating Pressure: | 0.1~1.0MPa(15~145psi) | |||||
| Proof pressure: | 1.5MPa(215psi) | |||||
| Temperature(ºC): | -20~70 | |||||
| Speed rang (mm/s): | 30~500 | |||||
| Adjustable Stroke(mm): | -5~0 | |||||
| Stroke tolerance: | (0~+1.0) | |||||
| Cushion Type: | Burmper | |||||
| Non-rotating Tolerance: | ±0.2° | ±0.15° | ±0.1° | |||
| Port Size: | M5X0.8 | PT1/8 | ||||
1.Non-rotary accuracy of the cylinder fully retracted state, the cylinder fixed plate can be rotated angle;
2.PT thread, NPT thread and G thread are available.
Stroke:
| Bore size(mm) | Standard Stroke(mm) | Max Stroke(mm) |
| 6 | 10 20 30 40 50 | 50 |
| 10 |
10 20 30 40 50 60 70 80 90 100 | 100 |
| 16 | 10 20 30 40 50 60 70 80 90 100 125 150 175 200 | 200 |
| 20 | 10 20 30 40 50 60 70 80 90 100 125 150 175 200 | 200 |
| 25 | 10 20 30 40 50 60 70 80 90 100 125 150 175 200 | 200 |
| 32 | 10 20 30 40 50 60 70 80 90 100 125 150 175 200 | 200 |
1.The 100mm range of non-standard travel range of more than a standard stroke restructuring, its dimensions for the previous standard stroke cylinder dimensions. Such as the stroke of 28 non-standard stroke cylinder is a standard stroke of 30 standard cylinder restructuring, its dimensions and the same.
Product feature
1.JIS standard is implemented.
2.The non-rotating precision is high and deflection of the end of rod is low, which is suitable for precise guide.
3.It adopts lengthening type sliding supporting guide. No additional lubricant is needed and it has good performance of guide.
4.Mounting holes on three sides facilitates multi-position mounting.
5.It is good resistance to bending and twisting moments.
6.Except for the axial, each side of the cylinder has installation orifices to provide several installation and fixation ways for the customers.
7.There are two groups of air intake and outlet at two sides of the cylinder for the actual ion.
8.Bumper in front of the barrel can adjust the stroke of cylinder and relieve impact.
9.Standard configuration of this series has magnet and the type without magnet is not available.
Installation & Usage:
1.When load changes in the work, the cylinder with abundant output capacity shall be ed.
2.Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.
3.Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.
4.Dirty substances in the pipe must be eliminated before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.
5.The medium used by cylinder shall be filtered to 40μm or below.
6.Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.
7.The cylinder shall be carried out test run without load before application. Prior to run, buffer shall be turned to the minimum and gradually released to avoid the damage on cylinder caused by excessive impact.
8.The cylinder shall avoid the influence of side load in operation to maintain the normal work of cylinder and extend the service life.
9.If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the surface. Anti-dust caps shall be added in air inlet and outlet ports.
){kind=link}